Pool Equipment Installation
This is equipment installation, not pool building. We install full equipment packages, salt systems, pool lights, and automation, then set them up and hand you the settings. Every install is quoted after a photo of the existing pad, because the plumbing you already have decides most of the labor.
Signs you need this
- One unit failed and the rest of the pad is only a few years old
- That is a single piece install. Matching one new component to healthy equipment is cheaper than a package, as long as the plumbing and the electrical can carry what you are putting on.
- Three or more units are original to the pool
- Once the pump, filter and heater are all past their service life, doing them one at a time means paying for the same plumbing work three separate times. A package rebuild is the cheaper path there.
- You want to switch the pool over to salt
- That is a salt system install and it starts with sizing to actual gallons. It also needs a look at metal on the pad and stone at the coping, because salt is harder on some materials than others.
- You control everything by walking outside and turning a dial
- Automation is the fix, and it is a wiring and control job rather than a plumbing one. The pump, heater and valves get tied to one panel so schedules stop depending on somebody remembering.
- The plumbing is a maze with no unions anywhere
- Every future repair on that pad starts with a saw. Rebuilding the connections during an install is not an upsell, it is what keeps the next filter clean from becoming a two hour job.
- The pad sits crowded and equipment is stacked against the wall
- Heat and access both suffer. A layout with no clearance runs hotter, fails sooner and costs more to service, so a package install is the moment to fix the arrangement rather than repeat it.
What is included
Included in the plan
- A written scope listing every model number going onto the pad
- Old equipment removed and hauled off, not left beside the fence
- Plumbing and unions rebuilt so the next service call is not a demolition
- Bonding checked and corrected where the pad does not meet code
- Startup done, settings written down, and the app connected before we leave
Extra, and always in writing first
- Pad rework when the existing plumbing is undersized for the new pump
- Electrical runs and subpanel work handled by a licensed electrician
- Removing an abandoned or bypassed heater during the same visit
- Adding a spillover actuator to an automation package
Extras need a written yes with the dollar amount before the work starts. No verbal add ons, ever.
What it costs
Quoted after a photo
The equipment costs what it costs. Labor is decided by what is already on the pad, which is why the photo matters more than your square footage. Undersized plumbing, a crowded pad, a failed bond, or a heater sitting in the way all add hours. For a straight pump swap the published band is $900 to $2,400+.
We do not publish a number the phone will not honour. See how pricing works.
What moves the price
A range is only honest if you can tell which end you are on. These are the things that decide it.
| Factor | What it does to the number |
|---|---|
| What the existing plumbing can carry | Pipe size sets the ceiling on flow. Putting a larger pump onto undersized suction lines means reworking pipe, and that decision gets made from a photo of the pad rather than from pool square footage. |
| Electrical supply at the pad | Some units need a different voltage or a dedicated circuit. When a licensed electrician has to run a new line or set a subpanel, that is separate work and it belongs on the quote as its own line. |
| Whether the bond is intact | Older pads in this area frequently have a broken or missing bond wire. Correcting it is required before new equipment is energized, and finding it early is far cheaper than finding it after. |
| How many pieces go on at once | The pipe work, the shutdown and the startup happen once for a package and repeat for each single swap. Doing three units in one visit costs less in labor than three visits across three years. |
| Access to the equipment pad | A pad reachable from a driveway is a straightforward day. One behind a locked side gate, down a slope, or fenced in on all four sides adds haul time to both the demolition and the install. |
Swap one piece or rebuild the whole pad
| One piece at a time | Full package | |
|---|---|---|
| When it fits | One failed unit, everything else healthy | Pump, filter and heater all near the end |
| Cost today | Lower, one unit and one connection | Higher up front, lower per unit installed |
| Labor repeated | Pipe work and startup happen again each time | Pipe work and startup happen once |
| Pad layout | You keep the arrangement you already have | Layout, unions and clearance get corrected |
| Published price to expect | A pump swap runs $900 to $2,400+ | Quoted after a photo of the whole pad |
Short version. Replace one piece when the rest of the pad has life in it. Once you are on your third unit in four years, a package rebuild stops the cycle of paying twice for the same plumbing.
Our process
Photograph the pad, wide
Include the panel and enough wall to see the plumbing runs. That is what tells us whether this is a swap or a rebuild.
Written scope with model numbers
You see exactly what is being installed. If you want to price the equipment yourself, the numbers are sitting right there.
Install and rebuild the connections
Unions where unions belong, so the next filter clean does not require a saw and a bad afternoon.
Start it up and hand it over
Speeds set, schedules written, app paired, and the settings left with you on paper instead of in our heads.
How long it takes
Wide photo of the pad and panel
Same day reply
Written scope with model numbers
Within one business day
Install day
Most jobs finish in one day
Startup, settings written down
Before we leave
Through a North Texas year
- January and FebruaryThe best install window of the year. Nobody is swimming, the calendar is open, and a pool that is down for a day or two while a pad gets rebuilt costs you nothing in lost use.
- MarchThe rush starts. Everybody discovers a dead pump the same week the water warms, and lead times on equipment stretch just as demand for install days peaks across Denton County.
- April and MayGood weather and a working pool make this the popular window for automation and salt systems. Book early, because these are the same weeks openings fill the schedule.
- June through AugustEmergency territory. Installs in this window are usually replacing something that quit in the heat, and the pool is down during the exact weeks you actually want it.
- September through DecemberThe quiet, sensible time to plan. Prices are not seasonal, so replacing tired equipment now buys you a full swim season with nothing on the pad waiting to fail.
Our water. What goes onto a pad has to survive water that is hard, around 150 to 250 parts per million of calcium, and a summer that pushes surface temperature past 90 degrees. Scale builds inside a heater core and on cell plates when calcium and pH climb together, so equipment gets sized with that in mind and startup includes a real balance target. Getting the water right on install day is what decides whether new equipment reaches its service life or falls short of it.
Common mistakes we get called to fix
Buying a pump by horsepower alone
A larger motor on undersized pipe moves no more water and wastes power trying. Flow is set by the plumbing you own, so the pipe gets measured before anybody picks a number off a box.
Installing new equipment onto a failed bond
Bonding ties every metal part to the same electrical potential. Skipping the correction because the old pump ran fine ignores that the risk is to people in the water, not to the equipment.
Leaving the old unit beside the fence
Removal and haul off should be in the scope in writing. An installer who leaves the corpse in your side yard has also probably left the connections unfinished behind the new unit.
Accepting an install with no model numbers on the quote
A single line and a total tells you nothing about what is going on your pad. Model numbers let you look up what you are buying, and any honest scope will list every one of them.
What to send us before a pool equipment installation Flower Mound quote
Send a photo of the pad. One clear picture usually shows the model numbers, the pipe size, whether unions exist, and whether the bonding wire is still connected. That settles most of a pool equipment installation Flower Mound quote before a truck ever moves. Add a photo of the breaker panel if you are adding a heater or converting to salt, because the electrical supply decides more of these jobs than the equipment choice does.
Ask for model numbers on the quote rather than category names. A pump described only by horsepower tells you nothing about flow, and horsepower is the most common way people end up with the wrong unit. We will also tell you when one swap is right and a full pad rebuild is not, which is the smaller job of the two. Pool equipment installation Flower Mound work onto a broken bond is work we will not do.
A pad photo tells us more than a phone call ever does. We can usually see the model, the pipe size, whether the bond is intact and whether this is a straight swap or a rebuild, all before a truck moves.
What this looks like on a real job
Photo slot
A real in-progress shot from a pool equipment installation job. Crew or equipment visible, not a stock backyard.
Photo slot
The finished result plus a clear photo of the equipment pad, the kind that goes into the photo report after every visit.
Everything under this service
Common questions
Do you build new pools?
No. We install and replace equipment on pools that already exist. If you need a shell dug we will say so rather than take the job.
Can I buy the equipment myself?
You can, though manufacturer warranty terms often differ on owner supplied units. We tell you what that changes before you order anything.
How long does a full equipment package take?
Most are a single day. A pad that needs plumbing rework or a new electrical run becomes two, and we tell you which one it is before we start.
Will a new pump save me money?
A variable speed pump pays back through runtime, not magic. We show you the speeds and hours we plan to run, so the estimate is built on your pool.
Start this week
Send the city and a pad photo. You get the plan before the first stop.